More products out of our product range

In this category you'll find a selection of products for hydraulic and electrical drive systems as well as electrical control systems, sensors and many more. You'll also find products from our remaining stock, some parts are used but 100% functional. For further information please see buyer's guide

Positioning-controllers-POS-123-P-PFN
Positioning controllers POS-123-P-PFN
• Digital positioning unit
• Printed circuit board in IP-65 housing
• Integrated power stage up to 2.6 A
• Analogue feedback signal (0... 10 V / 4... 20 mA)
• Control via Profinet interface
• Analog, freely scalable sensor interface
• Real, physical units such as mm or mm/s
• Internal profile generator for constant speed
• Individual profile definition by specifying accelerations, speed and decelerations
• Extended control technology with PT1 controller
• Error diagnostics and extended function check
• Simplified parameterization with WPC-300 software
1.337,50 EUR
plus 17% tax
Positioning-controllers-POS-123-P
SOLD OUT
Positioning controllers POS-123-P
• Digital positioning unit
• Printed circuit board in IP-65 housing
• Integrierte Leistungsstufe bis zu 2,6 A
• Integrated power stage up to 2.6 A
• Additional outputs (0... 10 V / 4... 20 mA)
• Analogue position and speed inputs
• Analogue feedback sensors
• Simple and intuitive scaling of the sensor
• Optional: start-up assistant for fast and simple adjusting of the control parameter
• Motion command values in mm resp. mm/s
• Internal profile definition by acceleration, velocity and deceleration
• Principle of stroke-dependent deceleration for fast and robust positioning
• NC profile generator for constant speed  
• Expanded closed loop control technology
• Highest positioning accuracy by using the drift compensation
• Usable with overlapped proportional valves and with zero lapped control valves
• Fault diagnosis and extended function checking
• Simplified parameterization with WPC-300 software 
1.116,75 EUR
plus 17% tax
Gear Box hollow shaft with Hydraulic Pump (Gear Pump) group 3
Gear Box hollow shaft with Hydraulic Pump (Gear Pump) group 3 selectable displacement
  • P.T.O. gear box
  • Hollow shaft with snap ring 1 3/8''
  • ratio i=1:3.8
  • size: group 3
  • attached hydraulic pump (gear pump) with selectable displacement from 20 up to 63 ccm/REV
244,45 EUR
plus 17% tax
Gear Box P.T.O / Gear Pump group 2 selectable displacement
SOLD OUT
Gear Box P.T.O / Gear Pump group 2 selectable displacement
  • P.T.O. gear box
  • P.T.O. shaft 1 3/8''
  • transmission: 1:3.8
  • size: group 2
  • attached hydraulic pump (gear pump) with selectable displacement from 4 up to 32 ccm/REV
221,13 EUR
plus 17% tax
Hydraulic Motor M+S MR160 with seal guard for sweeper brush
SOLD OUT
Hydraulic Motor M+S MR160 with seal guard for sweeper brush
  • hydraulic motor MR160 by M+S
  • displacement: 160 ccm/REV
  • ports : G 1/2’’
  • shaft: Ø 25 mm cylindrical with key A8 x 7 x 32
  • seal guard on front flange, eg. for FAUN sweepers
  • oval flange 2-hole SAE A
  • spool valve type
  • internal check valve
  • with high pressure seal kit
  • usage without drain line possible
  • OEM quality, made in Europe
  • optimized for small spaces
224,11 EUR
plus 17% tax
Steering wheel 320 conical front
Steering shifter, drive shifter FNR, for off road vehicles, IP67, HMFNR_2
  • Designed for rugged environment 
  • with horn button
  • Completely sealed (IP67 rating)
  • 3 drive positions, forward - neutral - reverse
  • With wiring harness (length 100mm) and DEUTSCH Connector
  • Fits on steering column size 38, 45 and 55mm
  • with locaing pin
  • Operating voltage range: 1 to 48 V
  • Solenoid load 3 A @ 12.8 Volt with arc suppression
149,19 EUR
plus 17% tax
Gear Box Hollow Shaft with Snap Ring with Hydraulic Pump (Gear Pump) group 2 selectable displacement
Petrol engine LIFAN 168F-2B, 6.5PS
  • Engine type: 4-stroke, 1 cylinder, air-cooled, OHV, petrol engine
  • Motor power: 11 Nm bei 2500 U/min, 395 (g / kw / h) Kraftstoffverbrauch, 6,5 PS / 4,8 kW bei 3600 U/min
  • Starting device: Electric start / pull starter
  • Fuel type: super-unleaded petrol
  • Tank capacity: 3,6 l
  • Oil fillings: 0,6 l
  • Oil type: SAE 15W40 winter / summer
  • Volume 7m in distance​ (dBA): 78
  • Ø crankshaft: 19,05 mm
228,13 EUR
plus 17% tax
Catalog image Gear Box Hollow Shaft with Snap Ring with Hydraulic Pump (Gear Pump) group 2 selectable displacement
Gear Box Hollow Shaft with Snap Ring with Hydraulic Pump (Gear Pump) group 2 selectable displacement
  • P.T.O. gear box
  • Hollow P.T.O. shaft 1 3/8'' with snap ring
  • transmission: 1:3.8
  • size: group 2
  • attached hydraulic pump (gear pump) with selectable displacement from 4 up to 32 ccm/REV
230,51 EUR
plus 17% tax
Hydraulic Motor M+S MR160 with seal guard for sweeper brush, splined shaft
SOLD OUT
Hydraulic Motor M+S MR160 with seal guard for sweeper brush, splined shaft
  • hydraulic motor MR160 by M+S
  • displacement: 160 ccm/REV
  • ports : G 1/2’’
  • shaft:  Ø 25,32 mm splined (SAE 6B)
  • seal guard on front flange, eg. for FAUN sweepers
  • oval flange 2-hole SAE A
  • spool valve type
  • internal check valve
  • with high pressure seal kit
  • usage without drain line possible
  • OEM quality, made in Europe
  • optimized for small spaces
234,41 EUR
plus 17% tax
Steering wheel 320 conical front
Steering shifter, 4 speed drive shifter FNR, for off road vehicles, IP67, HMFNR_3
  • Designed for rugged environment 
  • with horn button
  • 4 speed positions
  • Completely sealed (IP67 rating)
  • 3 drive positions, forward - neutral - reverse
  • With wiring harness (length 100mm) and DEUTSCH Connector
  • Fits on steering column size 38, 45 and 55mm
  • With locating pin
  • Operating voltage range: 1 to 48 V
  • Solenoid load 3 A @ 12.8 Volt with arc suppression
180,46 EUR
plus 17% tax
Hydraulik speed reducer gear box 5710 Berma RT190 front
SOLD OUT
Hydraulic Speed Reducer - Type 5710
  • Alternative to Berma RT190
  • Torque 1900 Nm
  • Ratio: 1:10.2
  • Input: hydraulic motor with shaft 25 mm, SAE A flange (e.g. CPRM)
  • sturdy design of cast iron
  • higher torque with simple gerotor motor
  • gear box oil recommendation: SAE 80W-90, 2 liters
570,26 EUR
plus 17% tax
Illustration lever valve monoblock 80 liter 1 section spring centered front
Lever Valve, 80 Liter, Spring Centered, 1 Section, with Pressure Relief Valve PRV 63 to 200 bar
  • monoblock valve
  • 80 l/min
  • 1 section
  • connections A&B: G 3/4’’
  • double acting
  • spring centered
  • pressureless flow in neutral position
  • max. working pressure: 315 bar
  • incl. pressure relief valve
  • pressure relief valve adjustable from 63 bar – 200 bar (standard: 120 bar)
146,88 EUR
plus 17% tax
Steering wheel 320 conical front
Steering shifter, turn signal, lamp switch, type TSI, for off road vehicles, IP67, HMTSI_1

TSI Shifter for off road vehicles with the following functions:

  • Turn signal / left - right
  • Hazard 
  • Low beam
  • High beam and flash light
  • Parking light
  • Horn 
  • Completely sealed (IP67 rating)
  • With wiring harness (length 100mm) and DEUTSCH Connector
  • Fits on steering column size 38, 45 and 55mm
  • Without locating pin
  • Operating voltage range: 1 to 48 V
  • Solenoid load 3 A @ 12.8 Volt with arc suppression
158,00 EUR
plus 17% tax
Lever valve overdrive effect pedal 60 liter 1 sektion front
Lever Valve, 60 Liter, Overdrive Effect Pedal, with Pressure Relief Valve PRV 160 to 315 bar
  • monoblock valve
  • 60 l/min
  • 1 sections
  • connections A&B: G 1/2’’
  • no pressure lockdown
  • overdrive effect pedal
  • max. working pressure: 315 bar
  • incl. pressure relief valve
  • pressure relief valve adjustable from 160 bar – 315 bar (standard: 220 bar)
119,56 EUR
plus 17% tax
Steering wheel 320 conical front
Steering shifter, turn signal, wiper, type TSI, for off road vehicles, IP67, HMTSI_2

TSI Shifter for off road vehicles with the following functions:

  • Turn signal / left - right
  • Wiper (2 speed)
  • Washer 
  • Completely sealed (IP67 rating)
  • With wiring harness (length 100mm) and DEUTSCH Connector
  • Fits on steering column size 38, 45 and 55mm
  • Without locating pin
  • Operating voltage range: 1 to 48 V
  • Solenoid load 3 A @ 12.8 Volt with arc suppression
158,00 EUR
plus 17% tax
Fixing plate PTO gear box group 2 and 3
Fixing plate / welding plate for P.T.O. gear box group 2 and group 3
  • Fixing plate for P.T.O gear box group 2 and group 3
  • Sigot diameter: 82,5 mm
  • Fixing hole diameter: 110 mm
  • Dimensions: 300 x 150 x 8,5 mm
19,12 EUR
plus 17% tax
17 to 32 (from a total of 42)